<font id="3t775"></font>

              <font id="3t775"><track id="3t775"><dfn id="3t775"></dfn></track></font>

              <var id="3t775"></var>
              歡迎光臨山東墨源數控設備有限公司官網為您提供:保麗龍雕刻機,五軸保麗龍刻機,四軸保麗龍雕刻機

              NEWSCENTER
              新聞資訊
              聯系我們

              18560023440

              王經理:18560023440
              地址:山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

              新聞資訊 當前位置:首頁 - 新聞中心 > 新聞資訊 >

              石材雕刻機容易出現什么故障?

              來源:http://www.ahdalei.com 時間:2021-07-01 

              我們在使用石材雕刻機的時候,肯定會在使用的過程中出現一些故障,那么這個時候我們就要知道是機械哪里出現了問題,并要及時地進行解決。這樣才能更好地進行使用。那么下面我們就來看一下吧。
              When we use the stone carving machine, there will certainly be some failures in the process of use, so at this time we need to know where the mechanical problems occur, and to solve them in time. Only in this way can it be used better. Now let's take a look.
              一、報警故障
              1、 Alarm failure
              超程報警,表示機器在運行過程中已達到端為位置,請按以下幾個步驟逐步檢查:
              The over travel alarm indicates that the machine has reached the end position during operation. Please check step by step according to the following steps:
              1、所設計的圖形尺寸是否超出加工范圍。
              1. Whether the designed graphic size is beyond the processing range.
              2、檢查機器電機軸與絲杠連接線是否松動,若則,請上緊螺絲。
              2. Check whether the connecting line between the motor shaft and the lead screw is loose. If so, tighten the screw.
              3、機器與計算機是否正確接地。
              3. Whether the machine and computer are properly grounded.
              4、當前座標值是否超出軟限位數值范圍。
              4. Whether the current coordinate value exceeds the range of soft limit value.
              二、非報警故障
              2、 Non alarm fault
              1、電腦運行,機器不動,檢查電腦控制卡與電器箱連接頭是否松動,如果是,就要及時地進行解決,將其進行固定。
              1. If the computer is running and the machine does not move, check whether the connector between the computer control card and the electrical box is loose. If it is, it is necessary to solve it in time and fix it.
              2、機器在回機械原點時找不到信號,有可能是機械原點處接近開關失靈。
              2. When the machine returns to the mechanical origin, the signal can not be found, which may be due to the failure of the proximity switch at the mechanical origin.
              三、輸出故障
              3、 Output fault
              1、不輸出,請檢查計算機和控制箱是否連接好。
              1. No output, please check whether the computer and control box are connected well.
              2、打開雕刻管理器的設置里空間是否已滿,刪除管理器內不用的文件。
              2. Open the engraving manager settings to check whether the space is full, and delete the unused files in the manager.
              3、信號線接線是否松動,檢查各線路的鏈接是否正常。
              3. Check whether the signal line wiring is loose and whether the links of each line are normal.
              我們在大致的了解了石材雕刻機的故障之后,我們就要及時地進行故障的處理,保障其后期的正常運行,這樣才能更好地將其投入到工作中。在石材雕刻機上面的選擇也可以來華捷數控看一下,其在這方面還是做的不錯的。
              After we have a general understanding of the fault of stone carving machine, we have to deal with the fault in time to ensure its normal operation in the later stage, so as to better put it into work. In the stone engraving machine above the choice can also come to Huajie CNC look, its in this respect or do a good job.