<thead id="hhzlf"></thead>
            <var id="hhzlf"><span id="hhzlf"><progress id="hhzlf"></progress></span></var><b id="hhzlf"><dl id="hhzlf"></dl></b>
            <sub id="hhzlf"></sub><b id="hhzlf"><dl id="hhzlf"></dl></b>

              歡迎光臨山東墨源數控設備有限公司官網為您提供:保麗龍雕刻機,五軸保麗龍刻機,四軸保麗龍雕刻機

              INFORMATION
              業內資訊
              聯系我們

              18560023440

              王經理:18560023440
              地址:山東省德州市齊河縣經濟開發區齊眾大道7號-2車間

              業內資訊 當前位置:首頁 - 新聞中心 > 業內資訊 >

              石材雕刻機在使用過程為什么要加水?

              來源:http://www.ahdalei.com 時間:2022-04-06 

              標配的石材雕刻機,墓碑雕刻機都是雙冷卻的,一方面由于石材材質較硬,所以在工作的時候要水冷刀頭,另一方面是水冷卻主軸,防止主軸溫度過高,對主軸起到一定的保護作用。不過如果客戶在不注意或者不按培訓步驟工作的話,就會出現不通水干燒的現象,對機器本身造成嚴重損害。
              The standard stone engraving machine and tombstone engraving machine are double cooled. On the one hand, because the stone material is hard, the water-cooled cutter head should be used when working. On the other hand, the water cools the spindle to prevent the spindle temperature from being too high and play a certain role in protecting the spindle. However, if the customer doesn't pay attention or doesn't follow the training steps, there will be no water and dry burning, which will cause serious damage to the machine itself.
              石材雕刻機主軸干燒容易導致的就是主軸發熱過度,溫度過高導致燒掉。一般主軸燒掉后,就得需要把壞的返廠維修。然后修好再從工廠發回來,這樣一來一回的周期大約1周左右,會嚴重耽誤正常加工工期,如果客戶那邊著急要訂單的話,會造成很大的損失。所以說客戶在加工的時候,一定要按照工廠技術員的培訓操作,保證機器的正常使用,延長機器的適用周期。
              The dry burning of the spindle of stone carving machine is easy to lead to excessive heating of the spindle and burning out due to too high temperature. The spindle needs to be returned to the factory for repair. Then repair it and send it back from the factory. This cycle is about 1 week, which will seriously delay the normal processing period. If the customer is anxious to order, it will cause great losses. Therefore, when processing, customers must operate according to the training of factory technicians to ensure the normal use of the machine and prolong the application cycle of the machine.
              二,如果石材雕刻機的主軸沒有通水冷卻,就會一直處于持續高溫發熱狀態。容易導致主軸出現抖動或者錯位,雕刻忽快忽慢,不穩定的現象。一方面會使精度會受到影響,另一方面主軸錯位會使得雕刻樣品錯位,雕刻出的樣品自然漏洞百出,非常不精細。
              2、 If the main shaft of the stone carving machine is not cooled by water, it will always be in a state of continuous high temperature heating. It is easy to cause shaking or dislocation of the main shaft, fast and slow engraving and instability. On the one hand, the accuracy will be affected. On the other hand, the dislocation of the main shaft will cause the dislocation of the carved samples. The carved samples are naturally full of holes and are very not fine.
              以上就是為大家介紹的有關3050保麗龍雕刻機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://www.ahdalei.com/
              The above is the detailed introduction of 3050 styrofoam engraving machine. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.ahdalei.com/